Valcom VIP-822 Dual Network Trunk Port -888.Voip.Store

Not Rated Yet
Rate the Valcom VIP-822 Dual Network Trunk Port

The VIP-822 Dual Networked Trunk Port allows most loop start terminal devices to be connected to a managed IP-based LAN/WAN.

Our Price: $328.95

Quantity

Valcom VIP-822 Dual Network Trunk Port Summary

Valcom VIP-822

The VIP-822 Dual Networked Trunk Port allows most loop start terminal devices to be connected to a managed IP-based LAN/WAN.

Valcom VIP-822 Core Features

2 RJ-11 FX0
2 RJ-11 telephone failover connection

Mounting
The VIP-822 is designed for wall or table mounting.
Wall: Using the bracket and screws provided, secure the VIP-822 to the wall.
Table: Provided with the VIP-822 are four rubber pads. Peel the pads from their carrier backing and place at the four corners of the bottom of the unit.
Rack: Following the assembly drawing, attach the two mounting ears to the VIP-822 unit. Using rack screws, mount the VIP-822 in an available 1U rack slot.

Power Connections
The preferred method of powering a VIP-822 is via a power over Ethernet switch meeting the 802.3af specification.
If the rear panel barrel connector is used for power, the preferred power supply is a Valcom VIP-324.
Make all required signal connections before applying power to the unit. If powering via 802.3af, make sure all signal connections via the rear panel are made then connect the VIP-822 to the Ethernet switch.
If power is supplied via the barrel connector, make sure all signal connections are secure. Attach the unit to the network via the front panel RJ-45 Ethernet connector. Apply power by plugging the power supply in to the VIP-822 via the barrel connector on the rear of the VIP-822.

Network Connection
The VIP-822 has one CAT-5 RJ-45 network connector on the front panel.
Use the supplied CAT-5 patch cable to connect the VIP-822 to an Ethernet switch. If the Ethernet switch is 802.3af compliant the VIP-822 will draw power from it.

Signal Connections
Trunk Connections:
Connect standard analog telephones to the VIP-822 via the rear panel RJ-11 jacks labeled Port 1 Line or Port 2 Line. Tip and Ring appear on pins 3 and 4 of these jacks.

Failover Connection
Connect standard analog telephones to the VIP-822 via the rear panel RJ-11 jacks labeled Port 1 Phone or Port 2 Phone. Tip and Ring appear on pins 3 and 4 of these jacks.

Status Indicator Lights:
The VIP-822 has 3 status indication lights on the front panel:
STATUS: Flashes then illuminates to indicate power.
LINK: Indicates 100 Mbit Ethernet connection when illuminates. No activity indicates 10 Mbit connection.
ACT: Indicator flashes to indicate network activity.

Valcom VIP-822 FXO Ports (Loop Start)

Peer-Peer, No Server Required
Auto Destination Programmable
DTMF Dial Select - 1024 Zones
1 to 11 Digit Dial Plans
Two Way – Transmit / Receive
POE 802.3af, Class 3, or Local Power 24 VDC
Can Use DHCP Servers to Acquire IP Addresses
Easy Windows® Based Setup
1 RJ45 Ethernet Connection
Front Panel Activity LED
Network Activity LEDs
Point to Point, Zones, Groups, All Call UDP, Multicast
Caller ID Information - Various Options
Applications
- Tie Lines
- PSTN Access
- Legacy Interface

Valcom VIP-822 Features

RJ-45 for network connection
2 RJ-11 FX0
2 RJ-11 telephone failover connection
Front panel activity LED
Network activity LEDs
2.5mm jack for DC
802.3af compliant

Valcom VIP-822 Specifications

Protocols
- DHCP, IGMP v3, UDP, TCP, HTTP, Telnet, FTP
Voice Algorithm
- G.711 (64kbits/s)(ulaw)
- Echo Suppression
Electrical Properties
- Voltage: 24 Vdc @ 250 mA
- IEEE 802.3af compatible, class 3 device
- Regulatory: FCC Part 15 Class A
Trunk Port
- Decodes Caller ID